Mcculloch Mac 3214 Manual

Posted : admin | On 19-04-2021



Download Service manual of McCulloch mac 3214 Chainsaw for Free or View it Online on All-Guides.com.

Brand: McCulloch

  • View and download the user manual for your McCulloch product.
  • McCulloch gas chainsaws use a carburetor with needles that regulate the inflow of gas during different engine speeds. These needles can be opened and closed slightly through adjusting screws on the outside of the carburetor. Adjusting the needles will help solve many engine problems and improve the overall performance of the engine.
  • How to Adjust the Needles on a McCulloch Chain Saw. Internal combustion requires fuel to blend with air. The carburetor handles this for Mcculloch chain saws, just as for any small gas-powered.
  • Garden product manuals and free pdf instructions. Find the user manual you need for your lawn and garden product and more at ManualsOnline.

User manuals: - McCulloch CS. McCulloch MacCat Super 16 AV / MacCat Super 18 AV / Mac 3210 / Mac 3212 / Mac 3214 / Mac 3216 / Mac 3516 / Mac 3516 AV / Mac 3816.

Category: Chainsaw

Type: Service manual

Model: McCulloch mac 3214 , McCulloch mac 3210 , McCulloch mac 3216

Pages: 5

McCULLOCH
Model
Mac 3210
Eager Beaver 2014,
Silver Eagle 2014
Mac 3216,
Bore
(1.4 in.)
(1.4 in.)
(1.4 in.)
(1.4 in.)
Manual
30 mm
30 mm
30 mm
30 mm
DispL
(2.1 cu. in.)
(2.1CU. in.)
(2.1 cu. in.)
(2.1CU. in.)
Type
Direct
Direct
SPARK PLUG. Recommended
alent for all models. Spark plug elec-
0.025
models. Note that spark plug has a ta-
ket. Tighten spark plug to 150 in.-lbs.
CARBURETOR AZamaClQM27
all models. Refer to CARBURETOR
dures and exploded views of Zama car-
Initial a4justment for both the low-
one turn open from a lightly seated po-
gine warm and running. Make certain
Adjust idle speed screw so engine
speed. Adjust low-speed mixture screw
then turn screw out (counterclockwise)
ate cleanly without hesitation. If en-
accelerating, adjust low-speed mixture
Readjust idle speed screw if necessary
2800-3300 rpm. Chain must not move
High-speed mixture screw should be
ance with saw under cutting load. Do
too lean (turned too far clockwise) as
may be exceeded and engine may be
overheating. Maximum no-load speed
exceed 11,000 rpm.
MC130), remove the air filter cover (1)
screws securing the filter base (3) and

Mcculloch Mac 3214 Chainsaw Manual

carburetor, and disconnect fuel line and
mounting screws to 30-40 in.-lbs.
IGNITION. All engines are
system. The ignition coil and electronic
ignition module (10—Fig. MC130),
Air gap between the fiywheel mag-
ule should be 0.010-0.015 in. (0.25-0.38
Loosen ignition module mounting
sired air gap. If air gap is excessive, en-
start.
bricated by oil mixed with the gasoline
when using McCulloch 2-cycle oil. If
oil designed for use in air-cooled,
a 20:1 ratio. Do not use oil designed for
tainer to mix the fuel and oil.
automatic chain oiling system. Recom-
and Sprocket oil. Oil designed for auto-
viscosity according to ambient tem-

Mcculloch Mac 3214 Manual

REPAIRS
An improperly sealed crankcase can
rough, have low power and overheat.
this manual for crankcase pressure test
cated, pressurize the crankcase and use

Mcculloch Mac 3214 Chainsaw Manual

gasket, seals, pulse line and castings
PISTON, RINGS AND
is necessary to remove the powerhead
inder from the crankcase as follows:
ing (13—Fig. MC131), bar and chain.
housing (24), fiiel tank (7) and oil tank
Remove the ignition module, air
Remove spark plug and install a suit-
a rope in spark plug hole to prevent the
Illustntions couit^y McCuUoch
391

Related Products for McCulloch mac 3214

Related Manuals for McCulloch mac 3214

McCulloch mac 3214: Frequently viewed Manuals

On the underside of McCulloch saws is a black and yellow tag; the upper number (“Power Mac Fuel Line Replacement by schematron.org HIPA Fuel Air Filter Gas Line Primer Bulb Spark Plug for McCulloch In Primer Bulb Fuel Line Filter For McCulloch Chainsaw How to replace fuel lines in a McCulloch chainsaw. DIY Videos.

Loading . Also, applies to the Mac chain saw.

thanks.. Read more.

Buy products related to mac chainsaw parts and see what customers say about HIPA Fuel Air Filter Gas Line Primer Bulb Spark Plug for Mcculloch . 2-Pack 14' Semi Chisel Saw Chain for McCulloch MAC Chainsaws - (14 .

Buy products related to mac chainsaw parts and see what customers say about HIPA Fuel Air Filter Gas Line Primer Bulb Spark Plug for Mcculloch . 2-Pack 14' Semi Chisel Saw Chain for McCulloch MAC Chainsaws - (14 .I have a Mac chainsaw.

All the fuel lines fell apart, including the bulb from sitting. So I guestimated the connections.

I need a diagram showing how to install gas line to carburator,Primer and gas tank on Macculloh chainsaw McCulloch Mac ChainsawNot getting gas through carb. Can squirt bulb and will run until that.

The manual for that chainsaw requires a 20 :1 mixture of non-McCulloch two-cycle oil. That is oz.

per gallon of unleaded gasoline regardless of what it says on the oil container. Listed below is a amazing picture for mcculloch fuel line diagram.

We have been looking for this image throughout on-line and it originate from reputable resource. If you are looking for any new ideas for your parts diagram then this mcculloch fuel line diagram photo must be on the top of guide or you might use it for an optional thought.

Pluming diagram for McCulloch Chainsaw? I Have a McCulloch chainsaw whose fuel line just rotted out. I have the new fuel line but need to verify the connections from fuel feed to primer ball, primer to carb, carb to fuel tank.

The lower carburetor nipple is large, for a 3/32' fuel line. The upper carburetor nipple is smaller, for a 1/8' fuel line.

I attached the fuel tank line with the filter on the lower (larger) nipple. I purchased a 1/8' fuel line and attached it to the smaller upper nipple and then to the primer bulb upper nipple, which I .Mcculloch model MAC chainsaw, gas genuine partsNeed correct routing of fuel line on McCulloch chain saw